Reverse Circulation (RC) Drilling Rig
Why needs reverse circulation drilling?
. When drilling the hole of diameter >250mm, which the annular
area between the drill pipe and inner surface of borehole is very
big.
. If using direct circulation drilling method, it needs very
powerful compressor with high air flow(even 2 – 3 compressors) to
get enough flushing speed to below all the cuttings out of hole.
. Otherwise, the cutting will stay in the hole and stuck the
drilling. Therefore it can make hole drilling very costly. In this
case, the reverse circulation drilling(RC drilling) will be the
better choice.
Roschen DTH Reverse Circulation Principle:
. It is opposite from DTH direct circulation drilling method.
. Air go to hammer via the annular area between outer pipe and
inner pipe and take the cuttings out of hole through the area of
inner pipe.
. Due to the smaller annular area and inner pipe area for air go
through, it can get very high flushing speed with low air flow from
compressor.
. In this way, it can save cost for drilling
Example of reverse circulation compared and DTH direct circulation
methods:
1. By DC Drilling:
2. Hole Size: 300 mm
3. Drill Pipe Dia. 114 mm
4. Annular area between pipe and wall: 0.06 m2
5. Needed flushing speed: 20 m/s
6. Needed air flow: 72 m3/min.
7. Conclusion: it need 2 air compressors and each one with 36
m3/min air flow
8. By RC Drilling
9. Hole Size: 300 mm
10. Dual drill Pipe Outer Dia. 114 mm
11. Dual drill Pipe Inner Diameter: 60 mm
12. Annular Area between inner and out wall of Dual pipe: 0.00324
m2
13. Needed flushing speed: 20 m/s
14. Needed flushing speed: 20 m/s
15. Needed air flow: 4 m3/min
. Conclusion: it only need 1 air compressors with 4 m3/min air flow
is good enough
. From above calculation, we can see that by RC drilling it needs
much lower air flow and can save the cost for compressor. This is
reason why Reverse Circulation is widely used in borehole drilling
industry
Roschen Drills Reverse Circulation Accessories:
. RC Drilling Rig
. Air Compressor
. Air Inlet Swivel
. Dual Wall Pipe
. Special RC Connector
. RC Hammer
. RC Hammer Bit
. Cutting Collectors
More Articles
Underground Blasting Drilling
BlastHole Drilling Introduction
Drilling Rig Stability Calculation
Drilling Tools for Rotary Drilling Rig
Practical Aspects of Blast Hole Drilling
Introduction to Open Pit Mining
Hardrock Mining Drill Rigs Selection – Part Two
Hardrock Mining Drill Rigs Selection – Part One
How Drilling Tools Selection Impacts Borehole Quality
TOP 6 BRAND / Manufacturer For Drill Rigs
How to Select DTH Hammer Drill Bit
How to Select Rotary / Tricone Drilling Bit
7 Rules on How to Design Reverse Circulation System
6 Advantages of Reverse Circulation Vs Direct Circulation On Bore
hole drilling
8 Points on How to Select Water Well Drilling Rig
Market Survey Metals – Iron Ore
Market Survey Metals – Bauxite, Alumina, Aluminium
7 Rules of Thumb for Open Bit Blast Pattern
Mineral Commodity Summary
Down The Hole Drilling Trouble Shooting – Bit Damage
Down The Hole Drilling Trouble Shooting – Hammer Piston Casing
Breakage
Down The Hole Drilling Trouble Shooting – Treaded
Selection of DTH Drilling Tools
Rotary Drilling Method
General Drilling Method and Application
DTH Drilling Care & Maintenance – Part One
DTH Drilling Care & Maintenance – Part Two
Basic DTH and Top Hammer Drilling Knowledge
Well Drilling Method
Rock Properties
Rock Drillability
How to Repair Drill Bit
DTH(Down The Hole) Drilling Application
